Interactions of a Deformable Wheel with a Deformable Support Surface

Main Article Content

Kovbasa Volodymyr
5826Priliepo Nataliia

Abstract

The article analyzes methods for solving problems on the drive systems' compacting effect on the support surface (soil). There are analyzed results of studies on the distribution of pressures and tensions in the contact surfaces depending on the propulsors' mechanical properties and the support surface's material. The article also includes an analysis of methods for formalizing contact surfaces and constructing mathematical models for determining the distribution of pressures, deformations, and tensions in the contact surfaces. Numerical methods for solving contact problems that have been used recently are not integral. To obtain such solutions, numerical FEM and DEM methods can be used for a specific problem, i.e. for a problem with a known geometric data source and specific mechanical properties of a contacting body. Based on the studies conducted, it was concluded that to understand the interaction of a deforming wheel with a deformable surface, it is necessary to use an analytical method for solving contact problems in a three-dimensional setting as the most general and productive. It’ll allow us to determine the geometrical dimensions and shapes of the contact spot, determine dependencies of the geometrical parameters of the wheel, rolling resistance, tension-strain state of the contacting surfaces depending on the loading conditions of the wheel, its mechanical properties, and the support surface.

Downloads

Download data is not yet available.

Article Details

How to Cite
[1]
Kovbasa Volodymyr and 5826Priliepo Nataliia , Trans., “Interactions of a Deformable Wheel with a Deformable Support Surface”, IJITEE, vol. 13, no. 9, pp. 1–4, Aug. 2024, doi: 10.35940/ijitee.I9944.13090824.
Section
Articles

How to Cite

[1]
Kovbasa Volodymyr and 5826Priliepo Nataliia , Trans., “Interactions of a Deformable Wheel with a Deformable Support Surface”, IJITEE, vol. 13, no. 9, pp. 1–4, Aug. 2024, doi: 10.35940/ijitee.I9944.13090824.
Share |

References

Kononov, A. (1974). “Study of the implementation of traction and traction qualities and agrotechnical cross-country ability of wheeled tractors on loamy soil of Belarus”, PhD preview. Belarusian State Agricultural Academy, p. 41.

Zotsenko, M.L. et al. (2003). “Engineering geology. Soil mechanics, foundations and foundations”. Poltava: PNTU. p. 446.

Meirovitch, L. (1970) “Methods of analytical dynamics”. New York: McGraw-Hill, in series: Advanced engineering series. 526 p.

Golovchuk, A., Orlov, V., Strokov, O. (2003) “Operation and repair of agricultural machinery: in 3 volumes”. Kiev: Gramota. p. 335.

Solona, O.V., Kovbasa, V.P. (2020) “Justification of the parameters of working bodies for laying in-soil sprinklers”. Monograph. Vinnytsia, p.155. http://socrates.vsau.org/repository/getfile.php/28315.pdf

Timoshenko, S., Young, D. H. (1940) “Engineering Mechanics”. McGraw-Hill.

Kovbasa, V., Kurka, V., Pinchuk, V., Kadem, A. (2015) “Kinematics of interaction between a compacting roller and a soil layer of limited depth”. Motrol Commission of Motorization and Energetics in Agriculture, vol. 17, 3, pp. 270-276. https://nubip.edu.ua/sites/default/files/u329/motrol_17_3.pdf

Kovbasa, V., Solomka, A., Spirin, A., Kucheruk, V., Karabekova, D., Khassenov, A. (2020) “Theoretical determination of the distribution of forces and the size of the boundaries of the contact in the interaction of the deformable drive wheel with the soil”. Bulletin of the Karaganda university, Physics series, 3(99), pp. 62-72. https://doi.org/10.31489/2020Ph3/62-7230

Kovbasa, V., Pinchuk, V., Kadem, A. (2015) “On the distribution of pressure in the zone of contact of a deformable wheel with a deformable medium under the condition of the inconsistency of geometric shapes”. Bulletin National University of Water and Environmental Engineering, Technical Sciences, vol. 2(70), pp. 479-487.

Wanshen, X., Yan, Z. (2016) “Design of manned lunar rover wheels and improvement in soil mechanics formulas for elastic wheels in consideration of deformation”, Journal of Terramechanics, 65, pp. 61-71. https://doi.org/10.1016/j.jterra.2016.03.004

Wang, Y., Sun, T., Lu, Y., Si, C. (2016) “Prediction for Tire-Pavement Contact Stress under Steady-State Conditions based on 3D Finite Element Method”, Journal of Engineering Science and Technology, 9(4), pp. 17-25. https://doi.org/10.25103/jestr.094.04

Guthrie, A. G., Theunis R. Botha, P. Schalk Els, (2017) “3D contact patch measurement inside rolling tyres”, Journal of Terramechanics, 69, pp. 13-21. https://doi.org/10.1016/j.jterra.2016.09.004

Prilepo N. V., Kovbasa V. P. (2021) “Prerequisites for the analysis of the interaction of a deformable wheel with a deformable support surface”. Problems and prospects for the development of agricultural machinery. Poltava: PDAU. pp. 14-18.

Li, J., Berger, E.J. (2001) “A Boussinesq–Cerruti Solution Set for Constant and Linear Distribution of Normal and Tangential Load over a Triangular Area”. Journal of Elasticity 63, pp. 137–151. https://doi.org/10.1023/A:1014013425423

Prilepo, N.V., Kovbasa, V.P. (2023) “Determination of deformations of the contact zone of the deformable wheel with the deformable support surface”. Problems and prospects of the development of agricultural machinery. Poltava: PDAU. pp. 126-129 https://dspace.pdau.edu.ua/handle/123456789/15193

Khatti, J., & Grover, Dr. K. S. (2021). Prediction of Geotechnical Properties of Soil using Artificial Intelligence Framework. In International Journal of Recent Technology and Engineering (IJRTE) (Vol. 10, Issue 4, pp. 218–227). https://doi.org/10.35940/ijrte.d6625.1110421

Mikhail, M., Keramatikerman, Dr. Mahdi, Chegenizadeh, Dr. A., Terzaghi, S., Burns, G., & Nikraz, P. H. (2020). Influence of Bagasse Ash on Compaction Behvaiour of Soil. In International Journal of Innovative Technology and Exploring Engineering (Vol. 9, Issue 5, pp. 987–990). https://doi.org/10.35940/ijitee.e2693.039520

Mousa, A., Nahazanan, H., Huat, B. K., Yusoff, Z., & Mustafa, M. (2019). Properties of Biomineralization Process in Various Types of Soil and Their Limitations. In International Journal of Engineering and Advanced Technology (Vol. 9, Issue 1, pp. 4261–4268). https://doi.org/10.35940/ijeat.a1756.109119

Waldaho, B. (2024). Design and Fabrication of a Tractor- Drawn Multi-Crop Planter. In Indian Journal of Agriculture Engineering (Vol. 4, Issue 1, pp. 7–18). https://doi.org/10.54105/ijae.e4491.04010524

Khan, Mohd. I., Khan, Dr. A. A., & Yadav, Dr. S. (2021). Mechanistic Analysis of Rigid Pavement for Wheel Load Stresses By Finite Element Method Considering Different Sub-Grade with Different Percentage of Metal Fibre. In Indian Journal of Transport Engineering (Vol. 1, Issue 2, pp. 1–9). https://doi.org/10.54105/ijte.a1901.111221

Most read articles by the same author(s)

1 2 3 4 5 6 7 8 9 10 > >>