Experimental and Numerical Analysis Over Power Series Nose Cone

Main Article Content

Vineet Kumar Rathi

Abstract

While designing aerospace vehicles, one of the most important factors to consider is drag. Drag force opposes the vehicle and causes it to slow down, which in turn requires more fuel to maintain flight. The vehicle nose cone plays a vital role in minimizing the drag during flight. The shape of the vehicle's body, as well as the fluid characteristics and orientation, can all have a significant impact on drag. To determine the most effective nose cone design, a study was conducted to test the aerodynamic performance of power series nose cone profiles using both experimental and computational techniques. All nose cone profiles with the same L/D ratio were assessed at 25 m/s speed with no angle of attack. The experimental data, including pressure, velocity, and drag, were then compared with computational data to ensure the accuracy of the wind tunnel experiments. The primary factor in determining the best shape for the subsonic flow range among all the nose cone profiles was the drag coefficient. The nose cone with a power of 0.25 was found to have the lowest drag coefficient at low subsonic speeds, making it the best-performing nose cone profile among those investigated. During take-off, drag is the most undesirable factor, as it can significantly impact the fuel efficiency of the vehicle. Therefore, it is crucial to have the least amount of drag possible. In this case, the nose cone with a power of 0.25 can be used in the initial stages of the rocket to minimize drag and maximize fuel efficiency.

Downloads

Download data is not yet available.

Article Details

How to Cite
[1]
Vineet Kumar Rathi , Tran., “Experimental and Numerical Analysis Over Power Series Nose Cone”, IJITEE, vol. 13, no. 3, pp. 13–22, Mar. 2024, doi: 10.35940/ijitee.C9812.13030224.
Section
Articles

How to Cite

[1]
Vineet Kumar Rathi , Tran., “Experimental and Numerical Analysis Over Power Series Nose Cone”, IJITEE, vol. 13, no. 3, pp. 13–22, Mar. 2024, doi: 10.35940/ijitee.C9812.13030224.
Share |

References

Anderson J.D., “Fundamentals of Aerodynamics”, McGraw-Hill, New York, NY, USA, 2007.

Subha, Rosy & D'rozario, Anthony Mario & Manojith, Sreeshin, “Study on Various Types of Nose Cone Profiles at Supersonic Speed Through Analytical”, Experimental And Numerical Simulation Methods. Journal of Xidian University. 14. 10.37896/Jxu14.6/312, 2020. https://doi.org/10.37896/jxu14.6/312

Yeshwanth, A. & Senthiil, P.V. “Nose cone design and analysis of an avion”, International Journal of Pure and Applied Mathematics, 119. 15581-15588, 2018.

Kumar, P. Kiran. "Analysis of nose cone of the missile." International Journal of Engineering Research and Applications, ISSN 2248-9622, 2020.

Rozario and Anthony Mario, "Study on Various Types of Nose Cone Profiles at Supersonic Speed through Analytical, Experimental and Numerical Simulation Methods."

Schinetsky P. A., B. T. Brooker, A. Treadway, S. M. Olcmen, S. E. Jones, “Numerical and experimental analysis of projectile nose geometry”, Journal of Spacecraft and Rockets, 52(5), 1515-1519, 2015. https://doi.org/10.2514/1.A33316

Foster N. F., G. S. Dulikravich, “Three-dimensional aerodynamic shape optimization Using genetic and gradient search algorithms,” Journal of Rockets and Spacecraft, 34(1), 36-42, 1997. https://doi.org/10.2514/2.3189

Deepak N. R., T. Ray, R. R. Russell, “Evolutionary algorithm Shape Optimization of a Hypersonic Flight Experiment Nose Cone”, Journal of Spacecraft and Rockets, 45(3), 2008. https://doi.org/10.2514/1.33826

Ranjan R. R., D. V. Parmar, H. K. Raipuria, P. B. Singh, “Innovative nose cone design of aircraft”, ASME International Mechanical Engineering Congress and Exposition, Texas, USA, November 2015. https://doi.org/10.1115/IMECE2015-50264

Garry A., Crowell Sr, “The Descriptive Geometry of Nose Cone”, 1996.

Varma A. S., G. S. Sathyanarayana, “CFD analysis of various nose profiles”, International Journal of Aerospace and Mechanical Engineering, 3(3), 26-29, 2016.

Harish S., D. Hasen, V. Giridharan, “Computational study on surface pressure distribution and base pressure distribution over parabolic series nose cone”, Journal of Chemical and Pharmaceutical Sciences, 9(2), 0974-2115, 2016.

Rafie, A. S. M., Magaidi, A. M., & Marzuki, O. F. (2019). Aerodynamic Performance of Biomimicry Snake-Shaped Airfoil. In International Journal of Engineering and Advanced Technology (Vol. 9, Issue 2, pp. 3319–3323). https://doi.org/10.35940/ijeat.b3560.129219

Mishra, N. K., Kumar, A. S., Ganesh, M., & Rehman Alam, M. A. (2019). Design of Minimum Length Supersonic Nozzle using the Method of Characteristics. In International Journal of Innovative Technology and Exploring Engineering (Vol. 9, Issue 2, pp. 1370–1374). https://doi.org/10.35940/ijitee.b6183.129219

P, D., Verma, A., Reddy, C. J., Suri S, J., & M, V. (2020). Boundary Layer Control of Airfoil using Rotating Cylinder. In International Journal of Recent Technology and Engineering (IJRTE) (Vol. 8, Issue 6, pp. 4742–4750). https://doi.org/10.35940/ijrte.e9862.038620

Shaheen, A., & Sinha, A. D. (2020). Crash Analysis of Aircraft Nose Prototype. In International Journal of Engineering and Advanced Technology (Vol. 9, Issue 6, pp. 204–213). https://doi.org/10.35940/ijeat.f1360.089620

Pandey, S., & Samanta, A. (2020). Real-time Forecasting of COVID-19 Prevalence in India using ARIMA Model. In International Journal of Management and Humanities (Vol. 4, Issue 10, pp. 78–83). https://doi.org/10.35940/ijmh.j0973.0641020

Most read articles by the same author(s)

1 2 3 4 5 6 7 8 9 10 > >>