Drilling Casing Design using Drilling Software at Well “Well X-01” Field “S”

Main Article Content

Dr. KRT. Nur Suhascaryo
Sulistyorini Widi Hastuti
Eko Suyanto

Abstract

Well "X-01" is a slant (J-Type) directional well and will be subjected to appropriate and technically qualified drilling casing planning in order to prevent problems such as burst, collapse, and tension that can cause increased internal and external pressure loads experienced by the casing. The methodology used in this research is document study and quantitative analysis in casing planning using Drilling Software by taking into account the loading acting on the casing, which is burst, collapse, tension, biaxial, and triaxial loads. Casing design planning for Well "X-01" is carried out by analyzing the casing setting depth based on PPFG data, considering kick tolerance, then casing planning is carried out using Drilling Software. The results of drilling casing planning in Well "X-01" Field "S" using Drilling Software, five design routes were obtained, that is conductor casing using X-52 casing; 157.5 ppf, surface casing using K-55 casing; 94 ppf, intermediate casing using K-55 casing; 54.5 ppf, kick tolerance 32.55 bbls, production casing using K-55 casing; 40 ppf, kick tolerance 42.1 bbls, and production liner using K-55 casing; 23 ppf, kick tolerance 69.08 bbls. The safety factor of each route met API standards for the durability of the selected casing. In well "X", casing planning can be a reference in the casing design process stage because optimal and safe results are obtained

Downloads

Download data is not yet available.

Article Details

How to Cite
[1]
Dr. KRT. Nur Suhascaryo, Sulistyorini Widi Hastuti, and Eko Suyanto , Trans., “Drilling Casing Design using Drilling Software at Well “Well X-01” Field ‘S’”, IJRTE, vol. 12, no. 3, pp. 47–51, Oct. 2023, doi: 10.35940/ijrte.C7869.0912323.
Section
Articles

How to Cite

[1]
Dr. KRT. Nur Suhascaryo, Sulistyorini Widi Hastuti, and Eko Suyanto , Trans., “Drilling Casing Design using Drilling Software at Well “Well X-01” Field ‘S’”, IJRTE, vol. 12, no. 3, pp. 47–51, Oct. 2023, doi: 10.35940/ijrte.C7869.0912323.
Share |

References

Hendri Kurniantoro, M. P. (2015). Evaluation of Casing Design Planning in SELONG-1 Well at Selong Field. Seminar Nasional Cendekiawan 2015, 505.

Noviandy, F. (2015). Evaluation and Optimization of Casing Design in Well X-9 Drilling Operation, Prabumulih, PT. Pertamina EP. Seminar Nasional Cendekiawan 2015, 387.

Putri, D. M. (2019). Analysis of Kick Tolerance Determination at Well R for Field Development A. 13-14.

Rubiandini, R. R. (2010). Casing Setting Depth Selection. Available: https://www.scribd.com/document/337039238/Dril-002-Casing-Setting-Depth-Selection.

Oscar Molina, V. V. (2017). Geologic Carbon Storage for Shale Gas Recovery. Energy Procedia, 9. https://doi.org/10.1016/j.egypro.2017.03.1713

S.S. Rahman, G. C. (1995). Casing Design Theory and Practice. Amsterdam: Development in Petroleum Science-Elsevier.

Pattillo, P. (2018). Elements of Oil and Gas Well Tubular Design. Elsevier.

Watt, H. (2017 , Juni 25). Drilling Techniques, Chapter 7: Casing . Edinburgh: Create Space Independent Publishing Platform. Retrieved from petrowiki.spe.org: https://petrowiki.spe.org/Hole_geometry.

Lapeyrouse, N. J. (2011, Februari 9). Drilling Formulas.Com. Retrieved from Kick Tolerance Calculation, Part of Formulas and Calculations for Drilling, Production, and Workover. Available: https://www.drillingformulas.com/kick-tolerance-calculation/

Knez Dariusz, d. (2010). Well Design Using Landmark Software . The International Journal of Transport & Logistics, Trnava, 45-47

Most read articles by the same author(s)

<< < 1 2 3 4 5 6 7 > >>